S11六面钻加工中心
根据产量及工艺可选加工模式，前进后出模式，板件加工完毕即可加工下长张板，整个过程中流畅，待机时间短。前进后出方式可以连线生产，前进前出模式，主要针对单人操作或者加工量不大的情况。
铣型，层孔，引孔，通孔，双面开槽，通槽
系统通过扫码识别加工信息，智能高效。
计算机操作，CAD画图，CAM导入，可直接导入DXF,MPR,XML 等开放数据格式，操作便捷。
采用双抓手导轨，抓料最大速度可达145M/MIN，智能检测孔位信息有效避开开孔位置，减少钻孔过程中换手时间。
配置气浮工作台和气浮压板，加工过程中板件上下表面形成气层，提高板件输送效率，同时避免划伤板料，压板钻孔同时完成，保证钻孔精度及效率，气排钻包安装位置独特，避免钻孔时板材浮动导致孔位爆边，偏差，并有效防止钻包积尘导致钻头卡死影响生产。
根据产量及工艺可选加工模式，前进后出模式，板件加工完毕即可加工下长张板，整个过程中流畅，待机时间短。前进后出方式可以连线生产，前进前出模式，主要针对单人操作或者加工量不大的情况。
吸尘效果更佳，工件除尘效果达80%。上钻吸尘口有两个，下钻吸尘口有一个
S11六面钻加工中心
S11 six-sided machining center
铣型，层孔，引孔，通孔，双面开槽，通槽
系统通过扫码识别加工信息，智能高效。
计算机操作，CAD画图，CAM导入，可直接导入DXF,MPR,XML 等开放数据格式，操作便捷。
采用双抓手导轨，抓料最大速度可达145M/MIN，智能检测孔位信息有效避开开孔位置，减少钻孔过程中换手时间。
配置气浮工作台和气浮压板，加工过程中板件上下表面形成气层，提高板件输送效率，同时避免划伤板料，压板钻孔同时完成，保证钻孔精度及效率，气排钻包安装位置独特，避免钻孔时板材浮动导致孔位爆边，偏差，并有效防止钻包积尘导致钻头卡死影响生产。
根据产量及工艺可选加工模式，前进后出模式，板件加工完毕即可加工下长张板，整个过程中流畅，待机时间短。前进后出方式可以连线生产，前进前出模式，主要针对单人操作或者加工量不大的情况。
吸尘效果更佳，工件除尘效果达80%。上钻吸尘口有两个，下钻吸尘口有一个
Milling, layer hole, pilot hole, through hole, double side slotting, through slot.
System is intelligent and efficient by scanning code to identify processing information.
Computer operation, CAD drawing, cam import, can directly import DXF, MPR, XML And other open data formats, easy to operate.
With double gripper guide rail, the maximum speed of material grabbing can reach 145m/min, the intelligent detection of hole position information can effectively avoid the opening position and Reduce the hand changing time in the drilling process.
Equipped with air floating table and air floating pressure plate, the upper and lower surfaces of the plate form air layer during the processing, which can improve the conveying efficiency of the plate, and avoid scratching the plate. The drilling of pressure plate is completed at the same time, which can ensure the drilling accuracy and efficiency. The installation position of air exhaust drilling package is unique, which can avoid the hole edge burst and deviation caused by the plate floating during drilling, and effectively prevent the bit stuck due to the dust accumulation in the drilling package, which can affect the production.
According to the output and process, the processing mode can be selected, and the forward and backward mode can be selected. After the plate is processed, the next long plate can be processed. The whole process is smooth and the standby time is short. The mode of forward and backward output can be online production, and the mode of forward and backward output is mainly aimed at the situation of single person operation or small amount of processing.
The dust collection effect is better, and the dust removal effect of workpiece reaches 80%. There are two suction ports in upper drilling and one suction port in lower drilling.
项目名称Project name
加工最小板材尺寸Minimum machining plate size 30*200mm
加工最大板材尺寸Maximum machining plate size 1200*3000
XU轴（双夹手）Xu axis (double grip)145m/min
YV轴（左右）YV axis (left and right)80m/min
ZW轴（上下钻孔）ZW axis (drill up and down)30m/min
A轴（侧靠）A axis (side)60m/min
直钻Direct drilling上垂直钻9 /18) 下垂直钻6/12
Upper vertical drilling (9 / 18) and
lower vertical drilling (6 / 12)
水平钻Horizontal drill2左+2右+2前+2后
2 left + 2 right + 2 front + 2 back
镂铣加工电主轴Cutting and milling spindle风冷*2 Air cooled * 2
板材厚度Plate thickness9-60mm
工作气压Working air pressure0.6-0.8Mpa
工作电压Working Voltage380V/50HZ